iCAx开思网

标题: moldflow2010中文语言包显示乱码 [打印本页]

作者: mig2000 时间: 2009-8-28 22:43
标题: moldflow2010中文语言包显示乱码
请教大家一个问题：
安装moldflow2010后，工作区的结果显示的都是乱码，不知道如何解决？
我安装的模块有：MPI2010+中文语言包、Adviser2010+中文语言包、MDL2010、CAD doctor2010；
都可以正常使用，在切换到中文语言时，MPI和Adviser都有结果显示乱码的问题。
在英文模式下一切正常。
系统是windows7旗舰版32位，难道和这个有关么？
乱码部分见下图。

作者: lizhaomin 时间: 2009-8-29 09:37
可能是2010对win7 的兼容性不好

作者: yuyin60079 时间: 2009-8-29 12:39

lizhaomin 发表于 2009-8-29 09:37
可能是2010对win7 的兼容性不好

不是这个原因，我也是WIN7 X64 上安装的moldflow 2010R2_sp1没发现这个小问题

作者: Jenner-liu 时间: 2009-8-30 15:06
你的系统是什么版本的？如果安装的繁体版的系统，有可能会导致简体软件乱码。

作者: qianzh85 时间: 2009-11-8 14:51

yuyin60079 发表于 2009-8-29 12:39

不是这个原因，我也是WIN7 X64 上安装的moldflow 2010R2_sp1没发现这个小问题

我的分析完以后也出现都是乱码,不知你的moldflow 2010R2_sp1 是在那下载的。
可否共享一下呢.

作者: yuyin60079 时间: 2009-11-10 13:53

qianzh85 发表于 2009-11-8 14:51

我的分析完以后也出现都是乱码,不知你的moldflow 2010R2_sp1 是在那下载的。
可否共享一下呢.

I’m pleased to announce the availability of Autodesk Moldflow Insight 2010 Release 2, Service Pack 1. The service pack is available through Auto-Update for customers that start Autodesk Moldflow Insight 2010 Release 2 and on Subscription Center.

Customers on active subscription can download Autodesk Moldflow Insight 2010 Release 2 Service pack 1 from Autodesk Subscription Center (www.subscription.autodesk.com). Once logged in, click on ‘Product Downloads’ on the left hand side of the screen. Then follow the links to the available Moldflow 2010 Release 2 Service Pack 1 products. The Autdesk Moldflow 2010 Release 2 Service Pack 1 requires Autodesk Moldflow 2010 Release 2 products to be installed as a base.

The major enhancements for the service pack are:
• Speed improvement and memory reduction for 3D Fill +Pack solver. The performance improvements are available for both single threaded and parallel analysis.
• Improved exit behavior in case a 3D Fill + Pack analysis has insufficient memory available.
• Resolved a problem in the temperature calculation for cases where there polymer flowed from
tetrahedral elements into beam elements.
• A solver and screen output fix for 3D gas assisted injection molding.
• Resolved an issue in Dual Domain meshing where properties assigned to the CAD model were not transferred to the Dual Domain mesh.
• Improvements in behavior for the Customer Error Reporting (CER) and the Customer Involvement Program (CIP).

作者: caisheng918@163 时间: 2009-11-10 18:16
不懂。在学习当中。

作者: andysu 时间: 2009-12-23 12:37
我在WIN7安装不上不知怎么回事

作者: frank991 时间: 2013-11-19 10:47
同求！

欢迎光临 iCAx开思网 (https://www.icax.net/)