iCAx开思网

标题: 【注意】关于ugnx1和ugnx2，ijk和r输出圆弧在fanuc……？ [打印本页]

作者: jiangmhu 时间: 2003-10-6 12:01
标题: 【注意】关于ugnx1和ugnx2，ijk和r输出圆弧在fanuc……？
请将附件下载后在机床上空走试一下（要有graphic功能）。
特别注意标明有问题的指令。
除了用ugnx1和ugnx2，ijk变成r外，其他的参数在ugpost中是一样的。
有人碰到过这样的问题吗？
谢谢大家！

作者: jiangmhu 时间: 2003-10-9 11:52
有人试验过吗？
我想知道是不是因为ugnx1的ugpost本身有问题？

作者: 小草 时间: 2003-10-14 09:21
在fauuc om控制器上i j會走一個圓弧過切　深受其害

作者: flash_star 时间: 2003-10-14 16:47
那是因为你的后处理没做好，IJK要做为非模态指令

作者: jiangmhu 时间: 2003-10-16 12:09

flash_star wrote:
那是因为你的后处理没做好，IJK要做为非模态指令

老大：不知道你看过程序没有（标出有问题的地方是不正确的指令，没有标有问题的地方是相同的位置用不同的后处理器（r或ijk生成的），跟ijk是否模态没关系（我已经实验过了）。你把程序上机床走走就知道了。
谢谢…………………………………………！

作者: jiangmhu 时间: 2003-10-16 12:12
用nx1后处理，走圆用r，打断，正常
(NC FILE NAME    : sk1_030927_03_620-386c-00_em8_f_3_rr)
(CREATED BY       : 267)
(CREATED DATE    : Sun Oct 05 13:01:59 2003)
(POST PROCESSOR : mill)
(UGPOST TCL FILE : D:\Program Files\EDS\Unigraphics NX\mach\resource\postprocessor\fanuc0.tcl)
(CUTTING TYPE    : Z-Level Milling)
(TOOLPATH NAME    : JX2)
(TOOL NAME       : EM8)
%
O1234
N0010 G21
N0012 G40 G17 G49 G94 G80 G90
N0014 G54
N0016 T00 M06
N0018 G0 X-34.784 Y14.165 S0 M03
N0020 G0 Z20.
N5838 G0 X71.462 Y-26.973
N5840 G0 Z-16.673
N5842 G0 Z-16.771
N5844 G1 Z-19.311
N5846 G1 X71.264 Y-22.246
N5848 G2 X71.248 Y-22.282 R15.655
N5850 G2 X70.107 Y-24.459 R15.729
N5852 G2 X64.321 Y-29.898 R15.729
N5854 G2 X56.749 Y-31.823 R15.853
N5856 G2 X56.702 Y-31.824 R15.853(用r设置后处理，正常）
N5858 G2 X45.619 Y-27.187 R15.76
N5860 G2 X42.055 Y-21.643 R15.863
N5862 G2 X37.983 Y-28.181 R47.768
N5864 G2 X44.266 Y-36.808 R15.774
N5866 G2 X44.891 Y-41.213 R15.844
N5868 G2 X44.401 Y-45.121 R15.844
N5870 G2 X33.844 Y-56.236 R15.744
N5872 G2 X29.146 Y-56.954 R15.737
N5874 G2 X15.24 Y-48.584 R15.737
N5876 G1 X14.902 Y-47.891
N5878 G1 X14.593 Y-47.199
N5880 G1 X14.33 Y-46.506
N5882 G1 X13.899 Y-45.202
N5884 G2 X.073 Y-47.308 R46.429
N5886 G2 X-5.638 Y-46.956 R46.429
N5888 G2 X-19.601 Y-43.042 R46.625
N5890 G2 X-25.725 Y-39.69 R47.386
N5892 G2 X-33.535 Y-33.345 R45.897
N5894 G2 X-41.353 Y-22.954 R46.779
N5896 G2 X-44.497 Y-16.027 R46.679
N5898 G2 X-46.545 Y-8.377 R46.83
N5900 G2 X-49.751 Y-8.707 R15.735
N5902 G2 X-63.128 Y-1.256 R15.735
N5904 G2 X-65.324 Y4.754 R15.686
N5906 G2 X-65.492 Y7.046 R15.742
N5908 G2 X-58.28 Y20.276 R15.742
N5910 G2 X-49.752 Y22.784 R15.754
N5912 G2 X-45.812 Y22.283 R15.754
N5914 G1 X-45.098 Y22.071
N5916 G1 X-44.427 Y21.853
N5918 G1 X-43.734 Y21.584
N5920 G1 X-42.38 Y20.991
N5922 G2 X-35.031 Y31.769 R45.958
N5924 G2 X-27.11 Y38.755 R46.247
N5926 G2 X-13.95 Y45.192 R47.151
N5928 G2 X-.017 Y47.301 R47.082
N5930 G2 X4.752 Y47.058 R47.082
N5932 G2 X18.606 Y43.483 R47.143
N5934 G2 X35.922 Y30.767 R47.185
N5936 G2 X46.312 Y9.604 R47.311
N5938 G2 X47.297 Y.008 R47.225
N5940 G2 X47.157 Y-3.626 R47.225
N5942 G2 X56.772 Y-.331 R15.676
N5944 G2 X62.936 Y-1.594 R15.676
N5946 G2 X69.862 Y-7.327 R15.641
N5948 G2 X72.456 Y-14.642 R15.708
N5950 G2 X72.523 Y-16.093 R15.655
N5952 G2 X71.248 Y-22.282 R15.655
N5954 G2 X68.614 Y-26.461 R15.729
N5956 G3 X66.877 Y-31.077 R7.
N5958 G3 X66.966 Y-32.192 R7.
N5960 G0 Z-16.771
N5962 G0 Z20.
N7254 M05
N7256 G91 G28 Z0.0
N7258 M30
%
(ACTUAL CUTTING TIME = 228.00109103660535000 min)
(TOTAL  MACHINE TIME = 237.54657664050913000 min)

作者: jiangmhu 时间: 2003-10-16 12:15
用ugnx1后处理，用ijk走圆，有问题
%
:0273
N0010 G21
N0012 G40 G17 G49 G94 G80 G90
N0014 G54
N0016 T01M06
N0018 G0 X-34.784 Y14.165 S50 M03
N0020 Z20.
N5838 X71.462 Y-26.973
N5840 Z-16.673
N5842 Z-16.771
N5844 G1 Z-19.311
N5846 X71.264 Y-22.246
N5848 G2 X71.248 Y-22.282 I-14.396 J6.153
N5850 G2 X70.107 Y-24.459 I-14.459 J6.192
N5852 G2 X64.321 Y-29.898 I-13.318 J8.369
N5854 G2 X56.749 Y-31.823 I-7.572 J13.928
N5856 G2 X56.702 Y-31.824 I0.0 J15.853(这句有问题；ij都有；走出一个惊世骇俗的圆：（）
N5858 G2 X45.619 Y-27.187 I.082 J15.761
N5860 G2 X42.055 Y-21.643 I11.271 J11.162
N5862 G2 X37.983 Y-28.181 I-42.45 J21.903
N5864 G2 X44.266 Y-36.808 I-8.857 J-13.052
N5866 G2 X44.891 Y-41.213 I-15.219 J-4.405
N5868 G2 X44.401 Y-45.121 I-15.844 J0.0
N5870 G2 X33.844 Y-56.236 I-15.25 J3.913
N5872 G2 X29.146 Y-56.954 I-4.698 J15.019
N5874 G2 X15.24 Y-48.584 I0.0 J15.737
N5876 G1 X14.902 Y-47.891
N5878 X14.593 Y-47.199
N5880 X14.33 Y-46.506
N5882 X13.899 Y-45.202
N5884 G2 X.073 Y-47.308 I-13.826 J44.323
N5886 G2 X-5.638 Y-46.956 I0.0 J46.429
N5888 G2 X-19.601 Y-43.042 I5.447 J46.307
N5890 G2 X-25.725 Y-39.69 I19.632 J43.127
N5892 G2 X-33.535 Y-33.345 I24.861 J38.582
N5894 G2 X-41.353 Y-22.954 I33.108 J33.048
N5896 G2 X-44.497 Y-16.027 I40.793 J22.689
N5898 G2 X-46.545 Y-8.377 I44.05 J15.895
N5900 G2 X-49.751 Y-8.707 I-3.206 J15.405
N5902 G2 X-63.128 Y-1.256 I0.0 J15.735
N5904 G2 X-65.324 Y4.754 I13.326 J8.274
N5906 G2 X-65.492 Y7.046 I15.574 J2.292
N5908 G2 X-58.28 Y20.276 I15.742 J0.0
N5910 G2 X-49.752 Y22.784 I8.528 J-13.246
N5912 G2 X-45.812 Y22.283 I0.0 J-15.754
N5914 G1 X-45.098 Y22.071
N5916 X-44.427 Y21.853
N5918 X-43.734 Y21.584
N5920 X-42.38 Y20.991
N5922 G2 X-35.031 Y31.769 I41.261 J-20.24
N5924 G2 X-27.11 Y38.755 I34.351 J-30.964
N5926 G2 X-13.95 Y45.192 I27.046 J-38.623
N5928 G2 X-.017 Y47.301 I13.933 J-44.974
N5930 G2 X4.752 Y47.058 I0.0 J-47.083
N5932 G2 X18.606 Y43.483 I-4.719 J-46.905
N5934 G2 X35.922 Y30.767 I-18.537 J-43.392
N5936 G2 X46.312 Y9.604 I-35.934 J-30.774
N5938 G2 X47.297 Y.008 I-46.24 J-9.596
N5940 G2 X47.157 Y-3.626 I-47.225 J0.0
N5942 G2 X56.772 Y-.331 I9.615 J-12.381
N5944 G2 X62.936 Y-1.594 I0.0 J-15.676
N5946 G2 X69.862 Y-7.327 I-6.089 J-14.407
N5948 G2 X72.456 Y-14.642 I-13.05 J-8.744
N5950 G2 X72.523 Y-16.093 I-15.588 J-1.451
N5952 G2 X71.248 Y-22.282 I-15.655 J0.0
N5954 G2 X68.614 Y-26.461 I-14.459 J6.192
N5956 G3 X66.877 Y-31.077 I5.263 J-4.616
N5958 G3 X66.966 Y-32.192 I7. J0.0
N5960 G0 Z-16.771
N7252 G0 Z20.
N7254 M05
N7256 G91 G28 Z0.0
N7258 M30
%

作者: jiangmhu 时间: 2003-10-16 12:16
以上为同一位置的加工程序，
以下三个为另一个地方。

作者: jiangmhu 时间: 2003-10-16 12:17
%
O0000
N0010 G21
N0012 G40 G17 G49 G94 G80 G90
N0014 G54
N0016 T00 M06
N0018 G0 X395.589 Y57.266 S0 M03
N0020 G0 Z20.
N2198 G0 X399.739 Y.173
N2200 G0 Z2.6
N2202 G1 X399.847 Y-1.568 Z2.447
N2204 G1 X400.929 Y-3.181 Z2.277
N2206 G1 X402.607 Y-4.016 Z2.113
N2208 G1 X404.547 Y-3.904 Z1.944
N2210 G1 X406.166 Y-2.83 Z1.774
N2212 G1 X407.022 Y-1.086 Z1.604
N2214 G1 X406.905 Y.785 Z1.44
N2216 G1 X405.839 Y2.409 Z1.27
N2218 G1 X404.099 Y3.273 Z1.1
N2220 G1 X402.161 Y3.143 Z.93
N2222 G1 X400.599 Y2.107 Z.766
N2224 G1 X399.726 Y.371 Z.596
N2226 G1 X399.847 Y-1.568 Z.426
N2228 G1 X400.929 Y-3.181 Z.256
N2230 G1 X402.607 Y-4.016 Z.092
N2232 G1 X404.547 Y-3.904 Z-.078
N2234 G1 X406.166 Y-2.83 Z-.248
N2236 G1 X407.022 Y-1.086 Z-.418
N2238 G1 X406.964 Y-.151 Z-.5
N2240 G1 X406.658 Y4.743
N2242 G2 X403.191 Y2.257 R11.296
N2244 G1 Y-2.264
N2246 G2 X406.911 Y-5.04 R11.229
N2248 G1 X406.964 Y-.151
N2250 G1 X410.964 Y-.111
N2252 G1 X410.965 Y-.048
N2254 G1 X410.063 Y14.419
N2256 G3 X408.415 Y15.072 R2.626
N2258 G1 X408.401
N2260 G1 X408.386 Y15.073
N2262 G3 X408.278 Y15.075 R2.526
N2264 G3 X405.752 Y12.549 R2.526
N2266 G3 X405.753 Y12.471 R2.526
N2268 G1 X405.756 Y12.376
N2270 G1 X405.753 Y12.281
N2272 G2 X399.191 Y5.256 R7.296
N2274 G1 Y-5.263
N2276 G2 X405.702 Y-12.132 R7.229
N2278 G1 X405.705 Y-12.196
N2280 G1 Y-12.26
N2282 G3 X407.146 Y-14.827 R3.017
N2284 G3 X408.274 Y-15.073 R2.704
N2286 G3 X409.45 Y-14.804 R2.704
N2288 G1 X409.484 Y-14.787
N2290 G1 X409.518 Y-14.772
N2292 G3 X410.823 Y-13.131 R2.296
N2294 G1 X410.964 Y-.111
N2296 G1 X405.976 Y-9.58
N2298 G3 X406.969 Y-9.651 R7.
N2300 G3 X413.969 Y-2.651 R7.
N2302 G1 Y-2.643
N2304 G1 X413.966 Y-.143
N2306 G1 X413.953 Y12.377
N2308 G1 X413.841 Y13.498
N2310 G1 X413.707 Y14.087
N2312 G1 X413.317 Y15.09
N2314 G1 X412.996 Y15.589
N2316 G3 X408.515 Y18.07 R5.626
N2318 G3 X408.278 Y18.075 R5.526
N2320 G3 X402.752 Y12.549 R5.526
N2322 G3 X402.755 Y12.377 R5.526
N2324 G2 X398.462 Y8.22 R4.296
N2326 G2 X398.432 Y8.219 R4.296（用r走圆弧，shang机校验正常）
N2328 G1 X396.192 Y8.226
N2330 G1 X396.191
N2332 G1 Y-8.242
N2334 G1 X397.312 Y-8.228
N2336 G1 X398.432
N2338 G1 X398.48
N2340 G2 X402.705 Y-12.267 R4.229
N2342 G3 X405.732 Y-17.476 R6.017
N2344 G3 X408.274 Y-18.074 R5.704
N2346 G3 X410.755 Y-17.505 R5.704
N2348 G3 X413.82 Y-13.387 R5.296
N2350 G1 X413.928 Y-12.267
N2352 G1 X413.974 Y-7.786
N2354 G1 X413.964 Y2.357
N2356 G3 X408.956 Y9.06 R7.
N2918 G0 Z20.
N2920 M05
N2922 G91 G28 Z0.0
N2924 M30
%

作者: jiangmhu 时间: 2003-10-16 12:18
%
O0000
N0010 G21
N0012 G40 G17 G49 G94 G80 G90
N0014 G54
N0016 T00 M06
N0018 G0 X395.589 Y57.266 S0 M03
N0020 G0 Z20.
N2198 G0 X399.739 Y.173
N2200 G0 Z2.6
N2202 G1 X399.847 Y-1.568 Z2.447
N2204 G1 X400.929 Y-3.181 Z2.277
N2206 G1 X402.607 Y-4.016 Z2.113
N2208 G1 X404.547 Y-3.904 Z1.944
N2210 G1 X406.166 Y-2.83 Z1.774
N2212 G1 X407.022 Y-1.086 Z1.604
N2214 G1 X406.905 Y.785 Z1.44
N2216 G1 X405.839 Y2.409 Z1.27
N2218 G1 X404.099 Y3.273 Z1.1
N2220 G1 X402.161 Y3.143 Z.93
N2222 G1 X400.599 Y2.107 Z.766
N2224 G1 X399.726 Y.371 Z.596
N2226 G1 X399.847 Y-1.568 Z.426
N2228 G1 X400.929 Y-3.181 Z.256
N2230 G1 X402.607 Y-4.016 Z.092
N2232 G1 X404.547 Y-3.904 Z-.078
N2234 G1 X406.166 Y-2.83 Z-.248
N2236 G1 X407.022 Y-1.086 Z-.418
N2238 G1 X406.964 Y-.151 Z-.5
N2240 G1 X406.658 Y4.743
N2242 G2 X403.191 Y2.257 I-8.196 J7.772
N2244 G1 Y-2.264
N2246 G2 X406.911 Y-5.04 I-4.711 J-10.193
N2248 G1 X406.964 Y-.151
N2250 G1 X410.964 Y-.111
N2252 G1 X410.965 Y-.048
N2254 G1 X410.063 Y14.419
N2256 G3 X408.415 Y15.072 I-1.734 J-1.972
N2258 G1 X408.401
N2260 G1 X408.386 Y15.073
N2262 G3 X408.278 Y15.075 I-.108 J-2.524
N2264 G3 X405.752 Y12.549 I0.0 J-2.526
N2266 G3 X405.753 Y12.471 I2.526 J0.0
N2268 G1 X405.756 Y12.376
N2270 G1 X405.753 Y12.281
N2272 G2 X399.191 Y5.256 I-7.291 J.234
N2274 G1 Y-5.263
N2276 G2 X405.702 Y-12.132 I-.711 J-7.194
N2278 G1 X405.705 Y-12.196
N2280 G1 Y-12.26
N2282 G3 X407.146 Y-14.827 I3.017 J.006
N2284 G3 X408.274 Y-15.073 I1.128 J2.458
N2286 G3 X409.45 Y-14.804 I0.0 J2.704
N2288 G1 X409.484 Y-14.787
N2290 G1 X409.518 Y-14.772
N2292 G3 X410.823 Y-13.131 I-.946 J2.092
N2294 G1 X410.964 Y-.111
N2296 G1 X405.976 Y-9.58
N2298 G3 X406.969 Y-9.651 I.993 J6.929
N2300 G3 X413.969 Y-2.651 I0.0 J7.
N2302 G1 Y-2.643
N2304 G1 X413.966 Y-.143
N2306 G1 X413.953 Y12.377
N2308 G1 X413.841 Y13.498
N2310 G1 X413.707 Y14.087
N2312 G1 X413.317 Y15.09
N2314 G1 X412.996 Y15.589
N2316 G3 X408.515 Y18.07 I-4.667 J-3.142
N2318 G3 X408.278 Y18.075 I-.237 J-5.521
N2320 G3 X402.752 Y12.549 I0.0 J-5.526
N2322 G3 X402.755 Y12.377 I5.526 J0.0
N2324 G2 X398.462 Y8.22 I-4.293 J.138
N2326 G2 X398.432 Y8.219 I0.0 J4.295（用ijk走圆弧，这句有问题）
N2328 G1 X396.192 Y8.226
N2330 G1 X396.191
N2332 G1 Y-8.242
N2334 G1 X397.312 Y-8.228
N2336 G1 X398.432
N2338 G1 X398.48
N2340 G2 X402.705 Y-12.267 I0.0 J-4.229
N2342 G3 X405.732 Y-17.476 I6.017 J.013
N2344 G3 X408.274 Y-18.074 I2.542 J5.107
N2346 G3 X410.755 Y-17.505 I0.0 J5.705
N2348 G3 X413.82 Y-13.387 I-2.183 J4.825
N2350 G1 X413.928 Y-12.267
N2352 G1 X413.974 Y-7.786
N2354 G1 X413.964 Y2.357
N2356 G3 X408.956 Y9.06 I-7. J-.008
N2358 G0 Z2.5
N2360 G0 Z20.

作者: jiangmhu 时间: 2003-10-16 12:20
用与前面两个相同的后处理文件，在ugnx2中处理，通过
%
O0000
N0010 G21
N0012 G40 G17 G49 G94 G80 G90
N0016 T00 M06
N0018 G0 X395.589 Y57.266 S0 M03
N0020 G0 Z20.
N2864 G0 X399.739 Y.173
N2866 G0 Z2.6
N2868 G1 X399.847 Y-1.568 Z2.447
N2870 G1 X400.929 Y-3.181 Z2.277
N2872 G1 X402.607 Y-4.016 Z2.113
N2874 G1 X404.547 Y-3.904 Z1.944
N2876 G1 X406.166 Y-2.83 Z1.774
N2878 G1 X407.022 Y-1.086 Z1.604
N2880 G1 X406.905 Y.785 Z1.44
N2882 G1 X405.839 Y2.409 Z1.27
N2884 G1 X404.099 Y3.273 Z1.1
N2886 G1 X402.161 Y3.143 Z.93
N2888 G1 X400.599 Y2.107 Z.766
N2890 G1 X399.726 Y.371 Z.596
N2892 G1 X399.847 Y-1.568 Z.426
N2894 G1 X400.929 Y-3.181 Z.256
N2896 G1 X402.607 Y-4.016 Z.092
N2898 G1 X404.547 Y-3.904 Z-.078
N2900 G1 X406.166 Y-2.83 Z-.248
N2902 G1 X407.022 Y-1.086 Z-.418
N2904 G1 X406.964 Y-.151 Z-.5
N2906 G1 X406.658 Y4.743
N2908 G2 X403.191 Y2.257 I-8.196 J7.772
N2910 G1 Y-2.264
N2912 G2 X406.911 Y-5.04 I-4.711 J-10.193
N2914 G1 X406.964 Y-.151
N2916 G1 X410.964 Y-.111
N2918 G1 X410.965 Y-.048
N2920 G1 X410.063 Y14.419
N2922 G1 X409.625 Y14.868
N2924 G1 X409.041 Y15.099
N2926 G1 X408.415 Y15.072
N2928 G1 X408.401
N2930 G1 X408.386 Y15.073
N2932 G3 X408.278 Y15.075 I-.108 J-2.524
N2934 G3 X405.752 Y12.549 I0.0 J-2.526
N2936 G3 X405.753 Y12.471 I2.526 J0.0
N2938 G1 X405.756 Y12.376
N2940 G1 X405.753 Y12.281
N2942 G2 X399.191 Y5.256 I-7.291 J.234
N2944 G1 Y-5.263
N2946 G2 X405.702 Y-12.132 I-.711 J-7.194
N2948 G1 X405.705 Y-12.196
N2950 G1 Y-12.26
N2952 G3 X407.146 Y-14.827 I3.017 J.006
N2954 G1 X407.889 Y-15.167
N2956 G1 X408.714 Y-15.159
N2958 G1 X409.45 Y-14.804
N2960 G1 X409.484 Y-14.787
N2962 G1 X409.518 Y-14.772
N2964 G1 X410.203 Y-14.463
N2966 G1 X410.676 Y-13.868
N2968 G1 X410.823 Y-13.131
N2970 G1 X410.964 Y-.111
N2972 G1 X405.976 Y-9.58
N2974 G3 X406.969 Y-9.651 I.993 J6.929
N2976 G3 X413.969 Y-2.651 I0.0 J7.
N2978 G1 Y-2.643
N2980 G1 X413.966 Y-.143
N2982 G1 X413.953 Y12.377
N2984 G1 X413.841 Y13.498
N2986 G1 X413.707 Y14.087
N2988 G1 X413.317 Y15.09
N2990 G1 X412.996 Y15.589
N2992 G3 X408.515 Y18.07 I-4.667 J-3.142
N2994 G3 X408.278 Y18.075 I-.237 J-5.521
N2996 G3 X402.752 Y12.549 I0.0 J-5.526
N2998 G3 X402.755 Y12.377 I5.526 J0.0
N3000 G2 X398.462 Y8.219 I-4.293 J.138
N3002 G1 X398.432（同前面的比较，同样的后处理设置，在ugnx2处理的结果）
N3004 G1 X396.192 Y8.226
N3006 G1 X396.191
N3008 G1 Y-8.242
N3010 G1 X397.312 Y-8.228
N3012 G1 X398.432
N3014 G1 X398.48
N3016 G2 X402.705 Y-12.267 I0.0 J-4.229
N3018 G3 X405.732 Y-17.476 I6.017 J.013
N3020 G3 X408.274 Y-18.073 I2.542 J5.107
N3022 G3 X410.755 Y-17.505 I0.0 J5.704
N3024 G3 X413.82 Y-13.387 I-2.183 J4.825
N3026 G1 X413.928 Y-12.267
N3028 G1 X413.974 Y-7.786
N3030 G1 X413.964 Y2.357
N3032 G3 X408.956 Y9.06 I-7. J-.008
N3034 G0 Z2.5
N3036 G0 Z20.
%

作者: 成浪 时间: 2003-12-29 11:53
我也碰到过.直到现在还没有好办法.

作者: tulip 时间: 2003-12-29 12:04
没遇到这种问题！

作者: zymtree 时间: 2003-12-29 18:50
用mdfa

作者: azul 时间: 2004-1-9 10:51
這是post的問題
因為你上x,y的值相差0.001

N2324 G2 X398.462 Y8.22 I-4.293 J.138
N2326 G2 X398.432 Y8.219 I0.0 J4.295

Y 8.22-8.219=0.001
你的控制器無法讀,所以跑互補圓
才會跑一大圈
你要判斷式修正

到nx2才有修正

作者: jiangmhu 时间: 2004-2-10 10:58

azul wrote:
這是post的問題
  因為你上x,y的值相差0.001
  
  N2324 G2 X398.462 Y8.22 I-4.293 J.138
  N2326 G2 X398.432 Y8.219 I0.0 J4.295
  
  Y 8.22-8.219=0.001
  你的控制器無法讀,所以跑互補圓
  才會跑一大圈
  你要判斷式修正
  
  到nx2才有修正
   

请问“判断式修正”是什么意思。
谢谢老大

作者: hualongcnc 时间: 2005-10-28 13:32
N2326 G2 X398.432 Y8.219 I0.0 J4.295（用ijk走圆弧，这句有问题）

作者: sgyj1 时间: 2005-10-28 16:41
azul wrote:
這是post的問題
  因為你上x,y的值相差0.001

  N2324 G2 X398.462 Y8.22 I-4.293 J.138
  N2326 G2 X398.432 Y8.219 I0.0 J4.295

  Y 8.22-8.219=0.001
  你的控制器無法讀,所以跑互補圓
  才會跑一大圈
  你要判斷式修正

  到nx2才有修正
  请说说看!!!!!!!

作者: xujiluo 时间: 2011-1-5 23:41
没错，终于找到了，我就是出现了这个问题，程式里有的地方 i或者 j后面数值为0。怎么没人解答啊
请版大看看啊

欢迎光临 iCAx开思网 (https://www.icax.net/)