iCAx开思网

标题: 求助程序只在换刀时加序号N 的后处理修改方法. [打印本页]

作者: 25068954 时间: 2010-12-26 10:58
标题: 求助程序只在换刀时加序号N 的后处理修改方法.
MASTERCAM 后处理的程序只在换刀的地方加上N 方便跳程序. 全部加N 程序又太大.

哪位帮忙解决一下不胜感谢!!!!!!!

作者: Visioncom 时间: 2010-12-26 22:49
方便跳程序是什么意思？加个N能大多少，DNC还在乎一个N？晕了。
什么样的需求都有啊，不过这个很好实现。
打开后处理，搜索“ n, ”,除了换刀部分的n,外，其他的DELETE掉就可以了。

作者: Visioncom 时间: 2010-12-26 22:51
还可以尝试一下N后的数值就是刀具号，不过没实际意义。

作者: 刘猛 时间: 2010-12-29 21:48
楼上的不知道就不要发表意见

作者: kimapro 时间: 2010-12-30 01:00
之前寫過此格式的後處理
備刀換刀刀具簡介程式簡潔無連續N碼
大批量產時如有需求可直接呼叫刀號刀號T11即N號 N11
轉出時如下

****************************************************
%
O0001( TEST.NC )
(DATE=30-12-10 TIME=00:42)
( T3 D43=0 H3 DIA=8.BALLMILL )
( T15 D55=0 H15 DIA=6. 6. BALLMILL )
G17G0G40G49G80
N3( T3 D43=0 H3 DIA=8.BALLMILL )
G80G91G28Z0M5
T3M6
M1
G54G0G90X-27.485Y9.845S6000M3
G43H3Z25.T15
M8
Z18.
G1Z15.F2000.
Y-.003Z13.266
Y0.F3500.
Y.003
Y-.001Z13.232
X-27.475Y-.662Z13.342
X-27.453Y-2.145Z13.452
X-27.428Y-3.806Z13.336
X-27.4Y-5.666Z13.011
X-27.382Y-6.868Z12.658
X-27.356Y-8.61Z11.963
X-27.331Y-10.268Z11.087
X-27.316Y-11.316Z10.403
X-27.294Y-12.782Z9.226
X-27.274Y-14.121Z7.897
X-27.256Y-15.318Z6.426
X-27.24Y-16.359Z4.823
X-27.227Y-17.227Z3.103
X-27.22Y-17.702Z1.896
X-27.214Y-18.113Z.575
G19G2Y-15.794Z5.975R18.585
Y-7.121Z13.272R18.739
Y-2.698Z14.484R18.565
Y5.28Z13.921R18.786
Y9.975Z11.794R18.597
Y17.272Z3.121R18.739
Y18.132Z.501R18.552
G1X-27.212Y18.136Z.475
X-27.103Y18.402Z.702
X-26.965Y18.738Z.716
X-26.809Y19.12Z.493
X-26.631Y19.554Z.008
Y19.148Z1.641
G3Y17.884Z4.866R19.844
G1Y16.875Z6.659
Y15.693Z8.331
...
...
...
...
...
G0Z35.M9
N15( T15 D55=0 H15 DIA=6.BALLMILL )
G80G91G28Z0M5
T15M6
M1
G54G0G90X-26.488Y9.845S6000M3
G43H15Z25.9T3
M8
G17Z18.9
G1Z15.933F2000.
Y-.003Z14.197
Y0.F3500.
Y.003
Y.008Z14.154
Y.048Z14.11
X-26.486Y.396Z14.13
Z14.19
X-26.483Y1.299Z14.183
X-26.481Y1.927Z14.158
X-26.476Y3.122Z14.018
X-26.471Y4.411Z13.782
X-26.465Y6.205Z13.277
X-26.458Y7.923Z12.583
X-26.453Y9.539Z11.696
X-26.447Y11.047Z10.642
X-26.442Y12.434Z9.434
X-26.437Y13.689Z8.085
X-26.433Y14.798Z6.606
X-26.429Y15.757Z5.011
Y15.939Z4.678
G19G3Y-16.061Z4.42R17.695
G1X-26.428Y-16.066Z4.387
X-26.383Y-16.676Z3.552
X-26.353Y-17.082Z2.825
X-26.323Y-17.49Z1.931
G2Y-13.711Z8.919R18.134
Y-7.072Z13.739R18.207
Y-.681Z15.155R18.092
Y4.619Z14.574R18.234
Y17.468Z2.005R18.199
G1X-26.322Y17.473Z1.957
X-26.263Y17.764Z1.668
X-26.172Y18.213Z.928
G3Y15.261Z7.685R18.542
Y8.445Z13.608R18.704
Y2.074Z15.514R18.517
Y-4.083Z15.179R18.792
Y-10.685Z12.261R18.542
Y-16.608Z5.445R18.704
Y-18.212Z.932R18.508
G1X-26.17Y-18.216Z.925
X-26.115Y-18.346Z.979
X-25.979Y-18.664Z.925
...
...
...
...
G0Z35.M9
G80G91G28Z0M5
G28Y0
M30
%
*******************************

作者: kgdc19 时间: 2010-12-30 09:56
如果程序后面的刀号小呢？

作者: 3zjun 时间: 2010-12-30 14:17
这个应该不难好像开思上有这样的后处理了楼主你自己找找看

作者: kimapro 时间: 2010-12-30 22:11
N碼與刀號相同
所以格式為

N5(T5XXXXX)
T5M6
N1(T1XXXXX)
T1M6
N24(T24XXX)
T24M6
XXX
XXX

作者: cechancao 时间: 2011-7-30 22:26
本帖最后由 cechancao 于 2011-7-30 22:27 编辑

fmt  N  4 nnnn       #Sequence number

  nnnn = t
   if stagetool >= zero, pbld, *wwww, *t, "M6", e

nnnn = t
   pbld, *wwww, *t, "M6", e

作者: yq-zheng 时间: 2012-11-3 21:54
怎么都没有解决这个问题的高手呀？

欢迎光临 iCAx开思网 (https://www.icax.net/)