【注意】关于ugnx1和ugnx2，ijk和r输出圆弧在fanuc……？

用与前面两个相同的后处理文件，在ugnx2中处理，通过
%
O0000
N0010 G21
N0012 G40 G17 G49 G94 G80 G90
N0016 T00 M06
N0018 G0 X395.589 Y57.266 S0 M03
N0020 G0 Z20.
N2864 G0 X399.739 Y.173
N2866 G0 Z2.6
N2868 G1 X399.847 Y-1.568 Z2.447
N2870 G1 X400.929 Y-3.181 Z2.277
N2872 G1 X402.607 Y-4.016 Z2.113
N2874 G1 X404.547 Y-3.904 Z1.944
N2876 G1 X406.166 Y-2.83 Z1.774
N2878 G1 X407.022 Y-1.086 Z1.604
N2880 G1 X406.905 Y.785 Z1.44
N2882 G1 X405.839 Y2.409 Z1.27
N2884 G1 X404.099 Y3.273 Z1.1
N2886 G1 X402.161 Y3.143 Z.93
N2888 G1 X400.599 Y2.107 Z.766
N2890 G1 X399.726 Y.371 Z.596
N2892 G1 X399.847 Y-1.568 Z.426
N2894 G1 X400.929 Y-3.181 Z.256
N2896 G1 X402.607 Y-4.016 Z.092
N2898 G1 X404.547 Y-3.904 Z-.078
N2900 G1 X406.166 Y-2.83 Z-.248
N2902 G1 X407.022 Y-1.086 Z-.418
N2904 G1 X406.964 Y-.151 Z-.5
N2906 G1 X406.658 Y4.743
N2908 G2 X403.191 Y2.257 I-8.196 J7.772
N2910 G1 Y-2.264
N2912 G2 X406.911 Y-5.04 I-4.711 J-10.193
N2914 G1 X406.964 Y-.151
N2916 G1 X410.964 Y-.111
N2918 G1 X410.965 Y-.048
N2920 G1 X410.063 Y14.419
N2922 G1 X409.625 Y14.868
N2924 G1 X409.041 Y15.099
N2926 G1 X408.415 Y15.072
N2928 G1 X408.401
N2930 G1 X408.386 Y15.073
N2932 G3 X408.278 Y15.075 I-.108 J-2.524
N2934 G3 X405.752 Y12.549 I0.0 J-2.526
N2936 G3 X405.753 Y12.471 I2.526 J0.0
N2938 G1 X405.756 Y12.376
N2940 G1 X405.753 Y12.281
N2942 G2 X399.191 Y5.256 I-7.291 J.234
N2944 G1 Y-5.263
N2946 G2 X405.702 Y-12.132 I-.711 J-7.194
N2948 G1 X405.705 Y-12.196
N2950 G1 Y-12.26
N2952 G3 X407.146 Y-14.827 I3.017 J.006
N2954 G1 X407.889 Y-15.167
N2956 G1 X408.714 Y-15.159
N2958 G1 X409.45 Y-14.804
N2960 G1 X409.484 Y-14.787
N2962 G1 X409.518 Y-14.772
N2964 G1 X410.203 Y-14.463
N2966 G1 X410.676 Y-13.868
N2968 G1 X410.823 Y-13.131
N2970 G1 X410.964 Y-.111
N2972 G1 X405.976 Y-9.58
N2974 G3 X406.969 Y-9.651 I.993 J6.929
N2976 G3 X413.969 Y-2.651 I0.0 J7.
N2978 G1 Y-2.643
N2980 G1 X413.966 Y-.143
N2982 G1 X413.953 Y12.377
N2984 G1 X413.841 Y13.498
N2986 G1 X413.707 Y14.087
N2988 G1 X413.317 Y15.09
N2990 G1 X412.996 Y15.589
N2992 G3 X408.515 Y18.07 I-4.667 J-3.142
N2994 G3 X408.278 Y18.075 I-.237 J-5.521
N2996 G3 X402.752 Y12.549 I0.0 J-5.526
N2998 G3 X402.755 Y12.377 I5.526 J0.0
N3000 G2 X398.462 Y8.219 I-4.293 J.138
N3002 G1 X398.432（同前面的比较，同样的后处理设置，在ugnx2处理的结果）
N3004 G1 X396.192 Y8.226
N3006 G1 X396.191
N3008 G1 Y-8.242
N3010 G1 X397.312 Y-8.228
N3012 G1 X398.432
N3014 G1 X398.48
N3016 G2 X402.705 Y-12.267 I0.0 J-4.229
N3018 G3 X405.732 Y-17.476 I6.017 J.013
N3020 G3 X408.274 Y-18.073 I2.542 J5.107
N3022 G3 X410.755 Y-17.505 I0.0 J5.704
N3024 G3 X413.82 Y-13.387 I-2.183 J4.825
N3026 G1 X413.928 Y-12.267
N3028 G1 X413.974 Y-7.786
N3030 G1 X413.964 Y2.357
N3032 G3 X408.956 Y9.06 I-7. J-.008
N3034 G0 Z2.5
N3036 G0 Z20.
%

我也碰到过.直到现在还没有好办法.

没遇到这种问题！

用mdfa

這是post的問題
因為你上x,y的值相差0.001
  
N2324 G2 X398.462 Y8.22 I-4.293 J.138  
N2326 G2 X398.432 Y8.219 I0.0 J4.295
  
Y 8.22-8.219=0.001
你的控制器無法讀,所以跑互補圓
才會跑一大圈
你要判斷式修正
  
到nx2才有修正
  

azul wrote:
這是post的問題  
  因為你上x,y的值相差0.001  
  
  N2324 G2 X398.462 Y8.22 I-4.293 J.138   
  N2326 G2 X398.432 Y8.219 I0.0 J4.295  
  
  Y 8.22-8.219=0.001  
  你的控制器無法讀,所以跑互補圓  
  才會跑一大圈  
  你要判斷式修正  
  
  到nx2才有修正  
   

请问“判断式修正”是什么意思。
谢谢老大

N2326 G2 X398.432 Y8.219 I0.0 J4.295（用ijk走圆弧，这句有问题）

azul wrote:
這是post的問題  
  因為你上x,y的值相差0.001  
   
  N2324 G2 X398.462 Y8.22 I-4.293 J.138   
  N2326 G2 X398.432 Y8.219 I0.0 J4.295  
   
  Y 8.22-8.219=0.001  
  你的控制器無法讀,所以跑互補圓  
  才會跑一大圈  
  你要判斷式修正  
   
  到nx2才有修正  
  请说说看!!!!!!!

没错，终于找到了，我就是出现了这个问题，程式里有的地方 i或者 j后面数值为0。怎么没人解答啊
请版大看看啊